频率设置

Sets the transmission frequency.

Unlock frequency field.

功率设置

Sets the output power level in watts.

Unlock power field.

射频静音

Selects the time after which the transmitter's output will be muted if the transmitter is transmitting silence.

Click 'Mute RF' to manually mute your transmitter.

Unlock mute rf button.

FSK

Sets interval between FSK messages.

Enter your FSK text into the box. This will be converted into morse code. Accepts text of up to 16 characters.

功率调整计划

Enables/disables Power Scheduling.

功率设置

Selects the output power that will be set during the scheduled interval

开始时间

Selects the time at which the output power will change from normal power to scheduled power.

结束时间

Selects the time at which the output power will change from scheduled power to normal power.

MPX源

Selects the source for the exciter. - Internal: selects internal generator. - External: selects MPX BNC input.

音频输入

Selects the input source.

预加重

Controls the pre-emphasis. Options are Off, 50 uS (Europe) and 75 uS (USA).

输入通道

Selects mono or stereo.

预设处理

Loads the audio processing preset.

类型

Configures the Alarm pin as an Alarm (Open Collector) or as an Analog Output (0 to 5 volts) to interface with Telemetry equipment.

源

Selects the parameter that will be reported as an analog voltage in the alarm pin. VOut = 5/1.2*CurrentValue/NominalValue. Please refer to the manual for further information.

源

Selects which detector is the source for the alarm.

门限

Selects the threshold at which the modulation level alarm will be activated. This parameter accepts values from 1000 to 100000.

门限

Sets the threshold at which the forward power alarm will be activated. This parameter accepts values from 0 to 2000.

门限

Sets the threshold at which the reverse power alarm is activated. This parameter accepts values from 0 to 2000.

门限

Sets the threshold at which the PA Temperature alarm will be activated. This parameter accepts values from 0 to 150

开机延时

Sets how long the error condition must occur for before an alarm is triggered. This parameter accepts values from 2 to 600.

关机延时

Sets how long the error condition must have stopped for before an alarm is un-triggered. This parameter accepts values from 2 to 600.

Email

Selects if an e-mail will be sent when the alarm state changes.

引脚极性

Selects whether the output is active high or active low.

启动

Enables/disables the trigger.

行动

Determines the action performed upon trigger.

Email

Selects if an e-mail will be sent when the alarm state changes.

短信

Sets the message that will be sent when the Trigger changes to ON. Accepts text of up to 300 characters.

RS232

Enables/disables logging to RS232.

文件

Enables/disables logging to file.

UDP

Enables/disables logging messages to a remote UDP logging/syslog server.

IP地址

Sets the IP address where the log messages should be sent via UDP. Accepts IPv4 address in the form www.xxx.yyy.zzz.

端口

Sets the port where the log messages should be sent via UDP. Disable UDP to change. This parameter accepts values from 1 to 10000.

Email

Sets the method used for sending emails. For simplicity, choose BW Broadcast.

从

Sets the email address of the sender. The unit will send e-mails through this address. Accepts text of up to 64 characters.

至

Sets the recipients of the emails. Multiple addresses must be separated by commas. Accepts text of up to 99 characters.

主机

Sets the IP address of the SMTP server. Accepts text of up to 64 characters.

端口

Sets the port number of the SMTP server. This parameter accepts values from 1 to 1024.

用户名

Sets the username for SMTP authentication. Must be left blank if no authentication is required. Accepts text of up to 64 characters.

密码

Sets the password for SMTP authentication. Must be left blank if no authentication is required. Accepts text of up to 64 characters.

每日最多邮件

Sets the maximum number of emails allowed to be sent by the unit in a single day to stop spamming from intermittent errors. This parameter accepts values from 1 to 1000.

Click 'Test e-mail' to trigger a test run of the e-mail settings above. If you do not receive the e-mail within a few minutes, check the settings are correct and try again.

RS232

Enables/disables the RS232 remote.

波特

Sets the RS232 baud rate.

远程登录

Enables/disables the telnet server.

端口

Sets the telnet TCP port. Disable Telnet to change. This parameter accepts values from 1 to 1024.

日期

Sets the date of the Real Time Clock. Accepts date in format dd/mm/yy.

时间

Sets the time of the Real Time Clock. Accepts time in format hh:mm.

位置

The physical location of this device (e.g., `TX Site 1, Rack 2'). Accepts text of up to 64 characters.

联系人

The contact details for the person who manages this device. Accepts text of up to 64 characters.

屏幕保护设置

This allows the time-out before the screensaver starts to be adjusted between 15s and 30 minutes.

前面板锁定

Enables/disables the screen lock code.

前面板锁定编码

Sets the screen lock code.